BrakesHow-To

How to Measure a Brake Rotor Ring and Find a Replacement (Alcon, AP Racing, Brembo)

Worn rings on an Alcon, AP Racing or Brembo big brake kit? Five measurements decide which replacement ring fits. Here is how to take them, what each one means, and how to match them to a Paragon ring.

  • 9 min read
  • Updated
  • By Chicane Australia
How to Measure a Rotor Ring tech guide cover with Paragon slotted rotor rings and bobbin hardware
Re-Ring or Replace? How to Rebuild 2-Piece Brake Rotors Reading How to Measure a Brake Rotor Ring and Find a Replacement (Alcon, AP Racing, Brembo) 9 minutes Next Re-Ring or Replace? How to Rebuild 2-Piece Brake Rotors

Short answer: to replace the ring on a 2-piece rotor you need five measurements: outside diameter, thickness, the bolt circle (PCD), the number and size of the mounting holes, and the pad depth. Match all five and the ring fits your hat and your caliper. Get one wrong and it will not bolt up, however close it looks. Once you have the numbers, type them into the Rotor Ring Finder and it shows the rings that match.

This guide walks through each measurement, the traps that catch people out, and how Paragon Performance rings cross over to Alcon, AP Racing, Brembo and Endless part numbers.

Slotted Paragon Performance replacement rotor ring with 12 mounting holes (product illustration)
A replacement rotor ring. The mounting holes around the inner edge are what bolt it to the aluminium hat.

Why you can't just order by diameter

A big brake kit rotor is two parts: an aluminium hat that bolts to the hub, and a cast iron ring that the pads clamp. The ring is the wearing part. When it is worn out you unbolt it from the hat and fit a new one.

The catch is that ring sizes are not standard between kit makers, or even within one maker's range. Take a very common size, 355 x 32mm. In Paragon's range alone that size is made with four different bolt circles:

  • PCD 215.9mm, 12 holes - replaces AP Racing CP4542-106/7
  • PCD 232.9mm, 12 holes - replaces Alcon DIV2216X770S36
  • PCD 233mm, 10 holes - replaces Brembo 09.5759.35/45 and Endless ER943
  • PCD 235mm, 12 holes - replaces Alcon DIV2146X037 and Endless ER940

All four are "355 x 32" rings. Only one of them fits your hat. That is why the full set of measurements matters.

What you need

  • Vernier or digital calipers (a steel rule works for diameter)
  • A pen and paper, or your phone
  • The wheel off, and ideally the rotor off the car

Before you measure anything, look for a part number. If one is still readable on the ring or on your kit paperwork, that is the fastest route: the Ring Finder has a part number search, and many Paragon rings list the Alcon, AP Racing, Brembo or Endless number they replace. If the number has worn or rusted away, measure.

The five measurements

1. Outside diameter

Measure edge to edge, straight across the centre of the ring. Typical big brake kit sizes run from about 280mm to 410mm. Paragon lists both metric and imperial, so a 362mm ring is also a 14.25 inch ring.

2. Thickness

Measure across the two braking faces with calipers. A worn ring measures thinner than it did new, so measure at the least worn spot you can find and round up to the nearest catalogue size. Common thicknesses are 28mm, 32mm, 34mm and 36mm for vented front rings. If your number lands between two sizes, check the lip at the outer edge, which the pads do not touch.

3. PCD (bolt circle)

PCD is the diameter of the circle that runs through the centre of the mounting holes. With an even number of holes, measure from the centre of one hole to the centre of the hole directly opposite.

Be precise here. Many AP Racing patterns are imperial, so a PCD of 215.9mm (8.5 inches), 228.6mm (9 inches) or 203.2mm (8 inches) is normal. Write down what you measure to the nearest half millimetre and let the finder do the matching, rather than rounding to a tidy number.

4. Mounting holes: how many, what size, what shape

Count the holes around the inner edge. Paragon rings come with 8, 10 or 12. Then look at the hole itself, because it tells you which bobbin system the rotor uses:

  • Round holes, for example 6.4mm or 9mm
  • Oval holes, for example 8.1 x 10.25mm
  • Rectangular slots, for example 9.5 x 15mm

Two rings can share a diameter, thickness and PCD and still differ here, so note the shape and measure the hole.

5. Pad depth (the "D" number)

This is the height of the braking face only: from the outer edge of the ring down to where the swept face ends, above the mounting tabs. It needs to suit your brake pad. A ring listed as D55 has a pad depth of about 55mm, and Paragon publishes it on its spec sheets as "Max Pad Depth", for example 55.5mm.

Pad depth is the measurement people skip. If it is too shallow for your pad, the pad overhangs the braking face.

Measurement cheat sheet

Measurement Paragon spec name How to take it
Outside diameter Outside Diameter "A" Edge to edge, across the centre
Thickness Thickness "B" Calipers across both braking faces
Bolt circle P.C.D. "M" Centre of one hole to the centre of the opposite hole
Mounting holes Number, Size and Type of Mounting Count them, measure one, note round, oval or rectangular
Pad depth Max Pad Depth Outer edge down to the end of the braking face

Paragon's spec sheets also list the internal diameter, the inside flange diameter, the mounting flange thickness and whether the flange face is flat or stepped. You rarely need these to find a ring, but they are useful as a final check if two rings look identical on the first five.

Left and right matter

Paragon rings use directional ventilation vanes, most often 48 or 72 of them, which pump air through the rotor as it turns. That makes the rings handed. Every pair is supplied as one left and one right, and they need to go on the correct side of the car. When you pull your old rings off, mark which side each came from.

Matching your numbers to a ring

With your measurements written down, there are three ways to find the ring:

  1. Use the Rotor Ring Finder. Type in the diameter, thickness, PCD, pad depth and bolt count, or tap the sizes you know and let it narrow the list.
  2. Search the original part number. If you know it, search it in the finder or the site search.
  3. Browse the Rotor Rings collection. Each listing shows the size, PCD and bolt count in the title.

Here are a few examples of how Paragon rings cross over to other brands' numbers:

Paragon ring PCD and mounting Replaces
370 x 36mm 209.55mm, 12 x 9mm round AP Racing CP3784-188/9
370 x 36mm 241.3mm, 12 x 6.4mm round AP Racing CP5772-6072/3
355 x 28mm 233mm, 10 x 8.1 x 10.25mm oval Alcon DIV2175X558
380 x 32mm 258mm, 10 x 8.1 x 10.25mm oval Brembo 09.5759.74/84
380 x 28mm 258mm, 10 x 8 x 10.25mm oval Brembo 09.A186.10/20

Notice the two 370 x 36mm rings at the top. Same diameter, same thickness, both for AP Racing rotors, and they are not interchangeable.

If your car has Paragon 2-piece rotors

You can skip the measuring. Paragon makes car-specific ring sets that are a direct replacement for its own 2-piece rotors, and those sets come with new rotor attachment hardware and assembly instructions. Look for your car in the Rotor Rings collection or the Paragon Performance range. Our guide to how 2-piece rotors work covers the rotors themselves.

What a Paragon ring is made of

Paragon casts its rings from CM-250, a high carbon alloy cast iron. The rings are heat treated to relieve stress, then finished by CBN surface machining. Paragon holds lateral run-out within 0.03mm and balances each ring to within 2 grams. The faces are slotted, which keeps the pad contact surface clean and helps in the wet.

Don't forget the hardware

The bolts and nuts that hold the ring to the hat are not part of a universal ring. Paragon recommends new hardware every time you replace rings, and the kit you need depends on your bobbin type (H, D, S or T). We cover that in our guide to rebuilding 2-piece rotors.

FAQ

Can I fit a Paragon ring to an Alcon, AP Racing or Brembo hat?

Yes, when the ring is made as a replacement for that pattern. Paragon lists the original part numbers its rings replace. Match the part number, or match all five measurements.

My thickness measures 31mm. Is it a 32mm ring?

Most likely. Rings wear thinner in use, so a worn 32mm ring will measure under 32mm. Check the unworn lip at the outer edge to confirm.

Are rings sold singly or in pairs?

In pairs: one left and one right. Replace both rings on an axle together.

Do I have to take the rotor off the car to measure it?

You can get diameter and thickness with the wheel off. PCD, hole size and pad depth are much easier and more accurate with the rotor on a bench.

What if nothing matches my measurements?

Email a photo of the ring and your measurements and we will match it for you. Brake work should be carried out by a qualified workshop.

Need help finding a ring? Contact our team at sales@chicaneaustralia.com.au.

Sources