{"product_id":"id-xds-injectors-hsv-e-series-ls3-w427-ls7-ve-34mm-set-of-8","title":"Injector Dynamics XDS Fuel Injectors - HSV E-Series LS3 (VE) \/ HSV W427 LS7 (VE) - 34mm Set of 8","description":"\u003ch2\u003eInjector Dynamics XDS Fuel Injectors - HSV E-Series LS3 (VE) \/ HSV W427 LS7 (VE) - 34mm Set of 8\u003c\/h2\u003e\n\u003cp\u003eA flow-matched set of 8 Injector Dynamics XDS injectors for HSV E-Series LS3 and the W427. Each injector has a 34mm body and a 14mm top o-ring to suit the 14mm fuel rail bore. The injectors are built to Injector Dynamics' specification in partnership with Bosch Motorsport, use the USCAR electrical connector, and are offered in four flow rates so you can match the set to your power target and fuel.\u003c\/p\u003e\n\u003cp\u003eWhat sets Injector Dynamics apart is the data. Every set is matched on both flow rate and offset (dead time), not just static flow, so each cylinder gets the same amount of fuel at idle and cruise as well as at full load. Injector Dynamics also publishes full characterisation data for every injector: offset from 8 to 16 volts and flow slope from 40 to 100 psi of differential pressure. Your tuner enters the real numbers instead of guessing, which is what lets a large injector still idle, cruise and start cleanly.\u003c\/p\u003e\n\u003ch3\u003eChoosing a Flow Rate\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eNominal flow\u003c\/th\u003e\n\u003cth\u003eMax fuel pressure\u003c\/th\u003e\n\u003cth\u003eFuel compatibility\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eID1050x\u003c\/td\u003e\n\u003ctd\u003e1065cc\/min\u003c\/td\u003e\n\u003ctd\u003e10.0 bar (145 psi)\u003c\/td\u003e\n\u003ctd\u003eAll known fuels\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eID1300x²\u003c\/td\u003e\n\u003ctd\u003e1335cc\/min\u003c\/td\u003e\n\u003ctd\u003e7.0 bar (101.5 psi)\u003c\/td\u003e\n\u003ctd\u003eAll known fuels (designed for alternative fuels)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eID1750x\u003c\/td\u003e\n\u003ctd\u003e1728cc\/min\u003c\/td\u003e\n\u003ctd\u003e7.0 bar (101.5 psi)\u003c\/td\u003e\n\u003ctd\u003eMethanol, ethanol, MTBE, nitromethane and all hydrocarbon fuels\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eID2600-XDS\u003c\/td\u003e\n\u003ctd\u003e2600cc\/min\u003c\/td\u003e\n\u003ctd\u003e9.0 bar (130.5 psi), minimum 11 volts\u003c\/td\u003e\n\u003ctd\u003eMethanol, ethanol and all hydrocarbon fuels. Not compatible with ethers (MTBE, ETBE, TAME) or nitromethane\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eID1050x (ID1050-XDS)\u003c\/strong\u003e: 1065cc\/min at 3.0 bar (43.5 psi) on petrol at 52°C. The evolution of the ID1000. Corrosion-resistant internals, an improved internal flow path and a stronger magnetic circuit for stable operation up to 10 bar.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eID1300x² (ID1300-XDS)\u003c\/strong\u003e: 1335cc\/min at 3.0 bar (43.5 psi) on iso-octane at 52°C. Designed with ethanol in mind, with all-stainless internals, but with a minimum fuel mass that still gives a good idle and cruise if you go back to petrol.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eID1750x (ID1750-XDS)\u003c\/strong\u003e: 1728cc\/min at 3.0 bar (43.5 psi) on E10 at 49°C. The successor to the ID1700. More flow with no increase in minimum fuel mass, better cylinder-to-cylinder balance at small pulse widths and improved pressure sensitivity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eID2600-XDS\u003c\/strong\u003e: 2600cc\/min at 3.0 bar (43.5 psi). The highest-flowing injector Bosch makes, 50% more than the ID1700x. Sets are Dual Slope Matched, which ID says cuts the average low pulse-width deviation from ±5.1% to ±1.4%.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNominal flow is measured at 3 bar (43.5 psi). Real flow goes up with fuel pressure: on a rising-rate system under boost the injector flows more than its rating, so check the maximum pressure above against your base pressure plus boost. If you are unsure which size suits your build, send us your engine, power goal, fuel and fuel pump and we will help.\u003c\/p\u003e\n\u003cp\u003eThe full list of cars this set suits is in the \u003cstrong\u003eVehicle Fitment\u003c\/strong\u003e tab. Engine swaps, aftermarket fuel rails and modified engines can change what fits, so if your car is not listed or has been modified, contact us before ordering.\u003c\/p\u003e\n\u003ch3\u003eBefore You Order\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck your fuel rail bore.\u003c\/strong\u003e This set suits 14mm rails. Several engines (Skyline GT-R, Supra, Silvia, MR2, RX-7) came with either 11mm or 14mm rails, and aftermarket rails vary, so measure or check your rail before ordering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eA tune is required.\u003c\/strong\u003e Bigger injectors must be set up in the ECU using the Injector Dynamics data. ID publishes ready-to-use data for common platforms including MoTeC M1, Haltech, AEM, Holley, MegaSquirt, Cobb and EcuTek, plus OEM-style GM and Ford tables. Some factory ECUs cannot scale to very large injectors.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector.\u003c\/strong\u003e The injectors use a USCAR connector. Older cars with a different plug need adaptors or harness changes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFuel supply and filtration.\u003c\/strong\u003e Size the fuel pump to suit the injectors. Injector Dynamics follows the Bosch specification for injector protection (at least 87% capture at 5 microns and 100% at 35 microns), fitted after the pump and as close to the rail as practical. The \u003ca href=\"\/products\/injector-dynamics-idf750-fuel-filter-black\"\u003eID F750\u003c\/a\u003e and \u003ca href=\"\/products\/injector-dynamics-f1250-inline-filter-only\"\u003eID F1250\u003c\/a\u003e filters are built to that standard.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e Injectors must be installed with a matching tune. Installation by a professional is recommended.\u003c\/p\u003e\n\u003ch3\u003eComplete Your Fuel System\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/injector-dynamics-idf750-fuel-filter-black\"\u003eInjector Dynamics F750 fuel filter\u003c\/a\u003e: meets the Bosch injector spec, with a Delta P indicator that shows when the element needs changing. Add the \u003ca href=\"\/products\/injector-dynamics-dual-fuel-sensor-id750\"\u003epressure \/ temperature sensor block\u003c\/a\u003e to log fuel pressure and temperature at the filter.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/injector-dynamics-f1250-inline-filter-only\"\u003eInjector Dynamics F1250 in-line filter\u003c\/a\u003e: 1,250 L\/h with only 1.1 psi drop for high-power builds, also available as a \u003ca href=\"\/products\/injector-dynamics-f1250-inline-filter-kit\"\u003ekit with mount\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/injector-dynamics-bpc100-e5lm-controller-kit\"\u003eInjector Dynamics FPS1100 pump system\u003c\/a\u003e (BPC100 controller + TI E5LM pump): holds up to 1,100 L\/h regardless of voltage or boost, enough for 2,000+ hp on ethanol from one pump.\u003c\/li\u003e\n\u003cli\u003eService parts: \u003ca href=\"\/products\/injector-dynamics-idf750-filter-element\"\u003eF750 element\u003c\/a\u003e, \u003ca href=\"\/products\/injector-dynamics-idf750-filter-oring\"\u003eF750 o-ring kit\u003c\/a\u003e and \u003ca href=\"\/products\/injector-dynamics-f1250-filter-element\"\u003eF1250 element\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp class=\"chicane-links\"\u003eShop more: \u003ca href=\"\/collections\/injector-dynamics\"\u003eInjector Dynamics Fuel Injectors\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003eNeed help confirming fitment? Contact our team at \u003ca href=\"mailto:sales@chicaneaustralia.com.au\"\u003esales@chicaneaustralia.com.au\u003c\/a\u003e.\u003c\/p\u003e","brand":"Injector Dynamics","offers":[{"title":"ID1050x (1050cc)","offer_id":52630662840613,"sku":"1050.34.14.15.8","price":1774.95,"currency_code":"AUD","in_stock":true},{"title":"ID1300x² (1300cc)","offer_id":52630662873381,"sku":"1300.34.14.15.8","price":3054.95,"currency_code":"AUD","in_stock":true},{"title":"ID1750x (1750cc)","offer_id":52630662906149,"sku":"1750.34.14.15.8","price":3924.95,"currency_code":"AUD","in_stock":true},{"title":"ID2600-XDS (2600cc)","offer_id":52630662938917,"sku":"2600.34.14.15.8","price":4664.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0918\/2943\/6709\/files\/1300.34.14.15.8_1_3_1.jpg?v=1782186148","url":"https:\/\/www.chicaneaustralia.com.au\/products\/id-xds-injectors-hsv-e-series-ls3-w427-ls7-ve-34mm-set-of-8","provider":"Chicane Australia","version":"1.0","type":"link"}